Surfboard, SUP and wetsuit care: what to do after salt water
Let me make a confession: however exciting an activity is, packing up, cleaning and looking after the kit afterwards doesn’t excite me nearly as much. I’m sure I’m not alone in that.
The easiest thing to do when you get out of the sea is to throw your kit in the boot and head home. Do that a few times and you might not run into any big problems straight away. But when kit like a surfboard, a SUP or a wetsuit is left salty, sandy or wet for long periods, its lifespan can get shorter. We’ve looked separately at what the heat itself does, on top of salt water, in our piece on how sea salt and summer heat wear out your kit.
Salt water won’t make this kit unusable after a few sessions. The real problem is salt, sand, sun and moisture staying on it for a long time. Fin fittings can seize up, metal parts can rust, a wetsuit can start to smell bad, and an inflatable SUP stored damp can develop mould or glue problems.
I lived by the sea, in a humid area, for many years. I saw with my own eyes how the paintwork on some cars parked along the seafront started to wear within a few years. Of course, we can’t conclude from that that “every car parked by the sea gets damaged in no time”. Still, I think it’s a good example of how much of an effect salty air and humidity can have in the long run. Anyway, back to the subject.
You don’t need complicated products or long cleaning routines to look after your surf and SUP kit. Rinsing with fresh water after every use, drying everything fully in the shade and storing it properly will usually be enough. In this guide, we’ll go step by step through caring for your surfboard, hard and inflatable SUP, wetsuit, leash, fins and paddle.
Why does salt water damage your kit?
To sum up the basic idea: when seawater dries on your kit, the salt in it leaves behind tiny crystals. This residue can build up especially in moving joints, zips, fin boxes and the points where paddle sections join.

Sand is abrasive in a similar way. Sand that gets into a wetsuit’s fabric surface, zip or seams can increase friction every time you use it. There are four main things to watch out for when caring for your kit:
- Salt
- Sand
- Sun and high temperatures
- Moisture that hangs around for a long time
The sun’s ultraviolet rays and high temperatures can damage a surfboard’s outer surface and some of its glued sections.
With inflatable SUPs, the air pressure inside the board can rise as the temperature goes up. If a board is left at full pressure for a long time on very hot ground, inside a car or in direct sun, the risk of damage around the seams, glue or valve increases. That’s why it’s important to keep an inflatable SUP out of direct sun and high temperatures when you’re not using it.
Firewire recommends rinsing the salt off surfboards and protecting them from the sun and high heat. Starboard also states that inflatable SUPs shouldn’t be left in the sun at full pressure for long periods.
Moisture, meanwhile, can lead to bad smells and mould, especially in wetsuits, deck pads and kit bags. I’ve had a bad experience with this myself. If you put your wetsuit away without cleaning it and don’t check on it until the next season, a very unpleasant surprise may be waiting for you.
So the point of looking after your kit isn’t just to keep it looking clean. You need to stop salt, sand, heat and moisture sitting on the materials for long periods.
What should you do first when you get out of the sea?
If you can, start looking after your kit before you head home.
If you can rinse your kit as soon as you’re out of the water, you stop the salt and sand drying on, and you won’t feel too lazy to clean up once you’re home, because you’ll have done most of the job on the beach.
If there’s fresh water on the beach, you can give the board, wetsuit and fittings a quick rinse. If there isn’t, it’s better to move your kit into the shade rather than leaving it in the sun, and clean it when you get home.
Last weekend I saw a SUP paddler rinsing their board with five-litre bottles of water they’d brought along. If there’s no shower at the campsite or on the beach, keeping a few bottles of water in the boot can be a very practical solution. Once you’re out of the sea, you can follow this order:
- Don’t drag the board across the sand.
- Don’t leave your kit in direct sun.
- Stop sand building up around the fins, leash and attachment points.
- Don’t leave your wetsuit wet in a closed bag for long.
- When you get home, rinse all your kit with fresh water.
- Wait until it’s completely dry before you store it.
Rather than putting wet, sandy kit straight into the car, you can use a large carry box or kit bag. But once the journey’s over, always take your wetsuit and any other wet kit out of the bag.
How to clean a surfboard
A surfboard doesn’t need washing with a chemical product after every session. In most cases, clean fresh water is enough. Rinse the board with low-pressure fresh water. Pay particular attention to these areas:
- Fin boxes
- Fin screws
- Leash attachment point
- Deck pad
- Rails
- The underside of the board
Salt and sand left in fin boxes or fitting screws can make the parts seize up over time. That’s why I’d recommend rinsing these areas especially carefully. After washing the board, you can wipe it with a soft cloth or leave it to dry in the shade. Stiff brushes and abrasive cleaning products can scratch the outer surface.
Firewire also recommends rinsing the surfboard and fin boxes with fresh water after every session and protecting the board from direct sun and high temperatures.
Should you remove the wax after every session?
No. You don’t need to strip all the wax off your surfboard after every session. You can lightly clean the sand and dirt off the surface of the wax. If the wax is very dirty, has lost its grip or has built up into a thick, uneven layer, you can give it a thorough clean.
Leaving the board in extreme heat for a long time to get the wax off isn’t the right way to do it. Use a wax comb and cleaning methods suited to the board’s material. Before using a chemical solvent, make sure the product is compatible with the board’s material.
Why check your surfboard for cracks?
Make a habit of giving your surfboard a visual check every time you clean it, even if it’s not a detailed one. Look out for these signs:
- Cracks
- Open dings
- Soft spots
- Dents on the rails
- Separation around the fin box
- Holes in the outer skin
Open damage that lets water into the inside of the board is particularly important.
If you’re not sure whether the damage is only cosmetic, show the board to an expert before you take it back in the water. The repair materials also need to suit the board’s resin and construction. With some epoxy boards, for example, using the wrong type of resin can make the existing damage worse. Firewire also specifically stresses using products that suit the board’s construction when making repairs.
How to clean an inflatable SUP
One of the most important rules of inflatable SUP care is not to roll the board up wet and sandy. It’s usually easier to clean the board while it’s still inflated. Rinse these areas with fresh water:
- The top and bottom of the board
- Deck pad
- Around the valve
- Fin box
- Carry handles
- D-ring fittings
- Bungee cords
If the fin is removable, it’s a good idea to clean the fin and the fin box separately. Sand can make the fin hard to fit and remove. Another important point: when you’re washing the board, don’t point high-pressure water straight into the valve. Cleaning around the valve with a soft cloth or low-pressure water is enough.
Starboard recommends rinsing an inflatable SUP with fresh water, especially after using it in salt water, and drying it completely before storing it. Red Paddle Co also states that kit should be rinsed with clean water, dried completely and then stored somewhere cool and dry.
Should you deflate an inflatable SUP straight away?
You can store an inflatable SUP either inflated or deflated. The decision depends on your storage space and the manufacturer’s recommendations. If you have suitable storage, you don’t have to deflate your SUP after every use. But if it’s going to stay inflated for a long time, stick to the pressure level the manufacturer recommends. If you’re storing the board inflated, it:
- Shouldn’t be in direct sun.
- Shouldn’t be left in a hot car.
- Shouldn’t touch anything sharp.
- Should sit on a flat surface or on suitable supports.
- Shouldn’t have anything heavy put on top of it.
If you’re going to deflate the board, wait until it’s completely dry. After opening the valve, roll it up in the direction the manufacturer recommends, without squeezing it too tightly. SUPs left wet for a long time can develop bad smells, mould and wear on their glued sections. Speaking for myself, even though deflating and rolling it up can feel like a chore sometimes, if my storage space is limited I find it more sensible to pack it away. But that’s entirely personal preference.
How to look after a hard SUP
If you use a hard SUP rather than an inflatable one, the basic care steps are very similar to looking after a surfboard. Rinse the board with fresh water. Pay particular attention to cleaning around the fin box, deck pad, leash attachment and carry handles. While you’re cleaning, check for:
- Cracks and dings
- Looseness in the fin box
- The deck pad lifting
- Damage to the leash attachment
- Dents on the rails
Using a board bag when you carry a hard SUP can reduce the risk of knocks and scratches. Don’t leave the board in direct sun, on hot ground or on a car roof for long periods. Dark surfaces can get very hot in the sun very quickly. If the board has an air-release (vent) valve, check the manufacturer’s instructions before you touch it. Not every board’s valve system works the same way.
How to wash a wetsuit
If you don’t want a bad experience like mine, the most important step in wetsuit care is to rinse it with fresh water after every use, however lazy you’re feeling. You can wash your wetsuit in cold or lukewarm water in a large tub or under the shower. Make sure you don’t use very hot water. Rinse the inside first. Then turn it right side out and clean the salt, sand and any other residue off the outside.
Here’s the basic washing order:
- Turn the wetsuit inside out.
- Rinse the inside with clean fresh water.
- Clean the zip and the entry area.
- Rinse the outside.
- Let the excess water drain off without wringing it.
- Leave it to dry in the shade.
Patagonia recommends rinsing a wetsuit with fresh water after every use, drying it inside out and not storing it in direct sun. The brand’s care instructions also say not to use a washing machine, tumble dryer, dry cleaning or bleach.
Can you wash a wetsuit with detergent?
A wetsuit doesn’t need washing with detergent after every use.
Regular rinsing with fresh water is usually enough for day-to-day care. If it starts to smell or gets very dirty, you can use a special cleaner made for neoprene or wetsuits.
Don’t use standard laundry detergent, bleach, fabric softener or harsh cleaning chemicals. These products can damage the fabric, the glued sections and the wetsuit’s stretch. When using a cleaner, follow the dosage and soaking time on the label. Using more product won’t clean your wetsuit any better. In fact, if it isn’t rinsed out properly, it can leave residue on the material.
You can find cleaners and care products made for wetsuits online or in water sports shops. I’ve used O’Neill‘s wetsuit cleaner before.
How to dry a wetsuit
One of the most common mistakes after washing a wetsuit is putting it in direct sun so it dries faster. Sun and high temperatures can make the wetsuit material stiffen, fade and lose its stretch over time. Dry your wetsuit:
- In the shade
- Somewhere with good airflow
- Away from heat sources
- Inside out first
- Then turned right side out
A thin, narrow hanger can stretch the shoulders of a wetsuit. You can use a wide wetsuit hanger or fold the wetsuit in half at the waist and hang it over the hanger. Patagonia also recommends drying a wetsuit folded at the waist. Don’t fold your wetsuit and put it in a closed cupboard or bag before it’s completely dry.
Why does a wetsuit smell?
Online, you’ll see plenty of complaints along the lines of “I wash my wetsuit regularly, but it still smells”. The most common reason is that the suit isn’t rinsed well enough, or it’s left damp in an enclosed space. Things that can cause the smell include:
- Not washing it with fresh water after the sea
- Rinsing only the outside
- Forgetting it, wet, in the car or in a bag
- Folding it before it’s fully dry
- Storing it somewhere without airflow
If it has started to smell, hand-wash your wetsuit with a suitable neoprene cleaner and rinse it thoroughly. Don’t try to cover up the smell with perfume, bleach or harsh chemicals. These products may mask the smell for a while, but they can damage the wetsuit’s material.
If your wetsuit is clean but still smells, check whether the zip, seams and thicker neoprene areas have dried out completely.
How to clean a leash, fins and paddle
Care doesn’t stop at the board and the wetsuit. Water shoes coming out of salt water deserve the same attention: left in a bag without a rinse, they’ll smell and their soles will stiffen over time. Leash: Rinse your leash with fresh water after every use. Make sure there’s no sand left in the attachment points, swivels or Velcro section. If the leash has cuts, has gone stiff or is coming loose at the attachment point, think about whether it needs replacing before you use it again.
Firewire also recommends rinsing your leash with fresh water after every use to get rid of salt and sand. Fins: If your fins are removable, take them out every so often and clean the fin box. Don’t overtighten the fin screw. Rather than forcing a sandy fitting apart, rinse it with fresh water first.
SUP paddle: Take multi-piece paddles apart after use and rinse the joints. Salt and sand can make the adjustment mechanism or the sections jam together. Wait until the paddle is completely dry, then store the sections separately or loosely fitted. SUP pump: Don’t put the pump down directly in seawater or sand. If there’s sand in the hose or the nozzle, clean it out. Make sure the pump is completely dry before storing it for a long time.
Starboard also recommends cleaning your SUP pump with fresh water and drying it completely.
How to store your kit
Where possible, store your kit somewhere cool, dry and out of direct sunlight.

Don’t think of the sun only in terms of heat here. Long-term UV exposure can also speed up wear on some materials.
Surfboards and hard SUPs
- Can be stored in a board bag or protective cover.
- Shouldn’t lean against sharp corners.
- Shouldn’t have anything heavy put on top of them.
- Shouldn’t be left in an overheated car.
Inflatable SUPs
- Should be completely dry.
- Shouldn’t be rolled too tightly.
- Should be stored somewhere cool and dry.
- Shouldn’t have the bag straps pressing too hard on the board.
Wetsuits
- Should be completely dry.
- Shouldn’t be kept on a thin hanger for long periods.
- Shouldn’t be folded sharply.
- Should be stored somewhere airy and out of the sun.
Before putting away kit you won’t be using for a while, it’s worth giving the fittings and surfaces one last check.
The most common kit-care mistakes
Not rinsing your kit with fresh water: Salt and sand keep building up on the fittings and surfaces.
Drying your wetsuit in the sun: It may seem to dry it faster, but in the long run it can speed up wear on the material.
Rolling up an inflatable SUP wet: Moisture can cause bad smells and mould. Leaving your board in a hot car: The high temperature inside a car can damage board materials and increase the internal pressure of an inflatable SUP.
Not clearing sand from around the fins and valve: Sand can make moving parts jam and put strain on fittings. Washing your wetsuit in a washing machine: The machine’s movement, the heat and standard detergent can damage the wetsuit’s structure.
Ignoring small dings on your board: Water getting in through open cracks can turn a small repair into a bigger problem. Forgetting wet kit in a bag: This is one of the most common causes of bad smells and mould.
Quick kit-care checklist after surfing and SUP
After every session, you can follow this short routine:
- Rinse the board with fresh water.
- Clean the fin box, valve and leash attachment.
- Wash the inside of your wetsuit first, then the outside.
- Take the paddle apart and rinse the sections.
- Clean the sand off the leash and fins.
- Move your kit out of direct sun.
- Dry the board and accessories completely.
- Dry your wetsuit in the shade, somewhere with good airflow.
- Check for cracks, cuts and loose fittings.
- Store everything only once it’s completely dry.
It varies with the type of kit, but after most sessions it doesn’t take very long.
The bottom line
When it comes to caring for your surfboard, SUP and wetsuit, a regular cleaning habit matters more than expensive care products.
Some of us buy a few cleaning products and only use them now and then. Yet rinsing your kit with fresh water after every use and storing it properly is usually far more effective than cleaning it with special solutions a few times a year.
Salt water and sand are a natural part of sea sports. What really damages your kit is leaving that residue on it uncleaned for long periods and storing wet kit in the wrong conditions. Rinsing with fresh water after every use, drying everything fully in the shade and spotting small damage early are the most effective steps you can take to make your kit last longer.
Don’t neglect the fin boxes and any cracks on your surfboard, the valve and deck pad on your inflatable SUP, or the inside and zip areas of your wetsuit. The few minutes you spend after getting out of the sea can save you from dealing with a seized fin, a smelly wetsuit or a SUP that’s been stored damp in the middle of the season.